| تعداد نشریات | 24 |
| تعداد شمارهها | 903 |
| تعداد مقالات | 8,081 |
| تعداد مشاهده مقاله | 15,203,324 |
| تعداد دریافت فایل اصل مقاله | 12,847,690 |
The Effect of Fe Additive on Plastic Deformation for Crush-Boxes with Closed-Cell Metal Foams, Part II: Al-Composite Foam-Filled brass tubes Compression Response | ||
| Iranian Journal of Materials Forming | ||
| مقاله 3، دوره 1، Issue 2، دی 2014، صفحه 23-31 اصل مقاله (665.62 K) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22099/ijmf.2014.2487 | ||
| نویسندگان | ||
| S.M.H. Mirbagheri1؛ J. Khajehali* 2 | ||
| 1Amirkabir university of technology | ||
| 2Amirkabir Univercity | ||
| چکیده | ||
| The brass tubes with foam cores of AlSi7SiC3, AlSi7SiC3Fe1 and AlSi7SiC3Fe3 were produced as the crush-boxes with circle and square cross-section. Then axial compressive behavior and energy absorption capability of the foam-filled tubes were investigated during the quasi-static progressive plastic buckling. The uniaxial compressive stress–strain curves of the foam-filled brass tubes exhibited that the compressive stress rose smoothly with the increase of the strain and no stress oscillations occurred in the plastic deformation region throughout the tests. The yield stress and the elastic modulus of the foam-filled brass tubes slightly decreased with increasing of the Fe wt. % in the foam cores. Also, with increasing of the Fe powder from 1wt. % to 3wt. %, the absorption energy of the foam-filled brass tubes decreased slightly dependent on the tubes cross-section. The strain-hardening exponent of the tubes with the Al7Si-3SiC-(+Fe) foam cores were found to be lower than the tubes with the Al7Si-3SiC foam cores with no Fe. However, increasing the Fe powder from 1wt. % to 3wt. % caused that the strain-hardening to be approximately eliminated and the plastic deformation behavior tends to be approximated to an ideal-plastic behavior up to the densification strain. Results show all of the compression responses are due to the Micro and Macro-defects within the foams cellular structure as well as the tubes cross-section geometry | ||
| کلیدواژهها | ||
| Metal foam؛ brass tube؛ plastic buckling؛ absorption energy؛ foam-filled tubes | ||
| مراجع | ||
|
[1] J. Baumeister, J. Banhart and M. Weber, Materials and Design, 18 (1997) 217–220. [2] T. Mukai, T. Miyoshi, S. Nakano, H. Somekawa and K. Higashi, Scripta Materialia. 54 (2006) 533–537. [3] A.G. Evans, M.F. Ashby, N.A. Fleck, L.J. Gibson, J.W. Hutchinson and H.N.G. Wadley, Metal Foams: A Design Guide, (2000), Elsevier. [4] M. Seitzberger, F.G. Rammerstorfer, R. Gradinger, H.P. Degischer, M. Blaimschein and C. Walch, Experimental studies on the quasi-static axial crushing of steel columns filled with aluminum foam, Int. J. Sol. Struct. 37(2000) 4125-4147. [5] M. Seitzberger, F.G. Rammerstorfer, H.P. Degischer and R. Gradinger, Crushing of axially compressed steel tubes filled with aluminum foam, Acta Mech. 125(1997) 93-105. [6] T. Daxner, H.J. Böhm, M. Seitzberger and F.G. Rammerstorfer, Modeling of Cellular Materials, Handbook of Cellular Metals. 2002: (Eds.:H.P.Degischer, B.Kriszt), pp. 245-280; Wiley-VCH, Weinheim, Germany. [7] M. Langseth, O.S. Hopperstad and A.G. Hanssen, Crash behavior of thin-walled aluminum members, Thin- Walled Structures, 32(1998) 127–150. [8] M. Langseth A.G. Hanssen and O.S. Hopperstad, Optimum design for energy absorption of square aluminum columns with aluminum foam filler. International Journal of Mechanical Sciences, 43 (2001) 153-176. [9] A. Bastawros, H. Bart-Smith and A.G. Evans, Experimental analysis of deformation mechanisms in a closed-cell aluminum alloy foam, Journal of the Mechanics and Physics of Solids, 48(2000) 301-322. [10]A.K. Toksoy and M. Guden, Partial A: Foam filling of commercial 1050H14 crash boxes: the effect box column thickness and foam relative density on energy absorption, Thin-walled structures 48(2010) 482-494. [11]W. Yan, E. Durif, Y. Yamada and C. Wen, Crushing Simulation of Foam-Filled Aluminum Tubes, Materials Transactions, 48-7 (2007) 1901-1906. [12]S.M.H. Mirbagheri and J. Khajehali, The effect of Fe additive on plastic deformation for crush-boxes with closed-cell metal foams, Part I: Al-composite foam compression response, Iranian Journal of Materials Forming, 1-1(2014) 32-45. [13]W. Deqing and S. Ziyuan, Effect of ceramic particles on cell size and wall thickness of aluminum foam. Materials Science and Engineering A, 361(2003) 45–49. [14] J. Banhart, Manufacture, characterization and application of cellular metals and metal foams, Progress in Materials Science, 46(2001) 559-632. [15]Mondal, M.D. Goel and S. Das, Effect of strain rate and relative density on compressive deformation behavior of closed cell aluminum-fly ash composite foam, Materials & Design, 30 (2009) 1268-1274. [16]M. J. Khajeali, Compressive response of the composite metallic foam filled-tubes and effective parameters, M.Sc. Thesis, Amirkabir University, 2011. [17]A. Daoud, Compressive response and energy absorption of foamed A359–Al2O3 particle composites, Journal of Alloys and Compounds, 486 (2009) 597–605. | ||
|
آمار تعداد مشاهده مقاله: 1,558 تعداد دریافت فایل اصل مقاله: 1,248 |
||