A Study of the Effects of Grain Size, Sheet Thickness and Punch Radii on Springback in Copper Sheets | ||
| Iranian Journal of Materials Forming | ||
| دوره 9، شماره 2، تیر 2022، صفحه 4-13 اصل مقاله (1.93 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22099/ijmf.2022.42544.1205 | ||
| نویسندگان | ||
| M.J. Lorestani؛ A. Adelkhani* | ||
| Department of Mechanical Engineering, Kermanshah Branch, Islamic Azad University, Kermanshah, Iran | ||
| چکیده | ||
| Sheet metal forming is one of the most common manufacturing processes in the production of many mechanical components and auto parts. Therefore, accurate investigation of the effects of important parameters in the sheet metal forming process is of primary importance for engineers and designers. In the present study, the effects of grain size, punch radii, and sheet thickness on the springback in the W-shaped bending dies are evaluated. The investigated metal sheets are composed of pure copper with three thicknesses of 0.1, 0.3, and 0.5 mm. In this research, the annealing heat treatment process is conducted for 60 minutes at 500, 750, and 900 degrees on the Celsius scale to study the grain size in copper specimens, then the recovery process is performed at ambient temperature. The experimental results revealed that the rise of annealing temperature results in the significant variations of metallographic structure and grain size. According to the results, for a constant thickness, the mechanical properties changed by increasing the annealing temperature. As the grain size increased, the elongation and yield strength decreased. With a constant annealing temperature, the yield strength and elongation fell with a decrease in thickness. However, in both cases Young’s modulus does not change much. The results also indicated that by increasing the thickness of the sheet under the same conditions of grain size, the springback angle decreased as well, so that the springback angle minimized through selecting the radii of 0.3 mm for the punch. Additionally, it was concluded that the springback angle can be minimized with a decrease in t/d ratio for a constant sheet thickness. Based on these results, a multiple-choice regression model has been employed that the average error of this model for springback prediction was 8.08%. | ||
| کلیدواژهها | ||
| Grain size؛ Thickness؛ Springback؛ Annealing temperature | ||
| مراجع | ||
|
[1] A. Adelkhani, H. Ebrahim, M.M. attar, The experimental and numerical study of the effects of welding angle on forming multilayered sheets in U-bending operations, Journal of Mechanical Science and Technology, 34(1) (2020) 239-244.
[2] H. Hou, G. Zhao, L. Chen, H. Li, Springback behavior and a new chord modulus model of copper alloy during severe plastic compressive deformation, Journal of Materials Processing Technology, 290 (2021) 116974.
[3] P. Hetz, S. Suttner, M. Merklein, Investigation of the springback behaviour of high-strength aluminium alloys based on cross profile deep drawing tests, Procedia Manufacturing, 47 (2020) 1223-1229.
[4] M. Cheraghi, A. Adelkhani, M.M. Attar, The experimental and numerical study of the effects of holding force and die radius on springback in a stretch bending test, Iranian Journal of Materials Forming, 8 (2) (2021) 35-43.
[5] S. Jadhav, M. Schoiswohl, B. Buchmayr, Applications of finite element simulation in the development of advanced sheet metal forming processes, BHM Berg-und Hüttenmännische Monatshefte, 163(3) (2018), 109-118.
[6] N. Şen, V. Taşdemir, Experimental and numerical investigation of the springback behaviour of CP800 sheet after the V-bending process, Ironmaking & Steelmaking, 48(7) (2021) 811-818.
[7] S.B. Chikalthankar, G.D. Belurkar, V.M. Nandedkar, Factors affecting on springback in sheet metal bending: a review, International Journal of Engineering and Advanced Technology, 3(4) (2014) 247-251.
[8] M.K. Choi, H. Huh, Effect of punch speed on amount of springback in U-bending process of auto-body steel sheets, Procedia Engineering, 81 (2014) 963-968.
[9] O. El Fakir, L. Wang, D. Balint, J.P. Dear, J. Lin, T.A. Dean, Numerical study of the solution heat treatment, forming, and in-die quenching (HFQ) process on AA5754, International Journal of Machine Tools and Manufacture, 87 (2014) 39-48.
[10] X, Liu, S. Zhao, Y. Qin, C. Wang, W.A. Wan-Nawang, Size effects on the springback of CuZn37 brass foils in tension and micro W-bending, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 232(14) (2018) 2439-2448.
[11] W. Phanitwong, A. Sontamino, S. Thipprakmas, Effects of part geometry on spring-back/spring-go feature in U-bending process, In Key Engineering Materials, 549 (2013) 100-107.
[12] A. Mkaddem, D. Saidane, Experimental approach and RSM procedure on the examination of springback in wiping-die bending process, Journal of Materials Processing Technology, 189(1-3) (2007) 325-333.
[13] D. Hakan, Ö. Mustafa, S. Murat, Effects of material properties and punch tip radius on spring-forward in 90 V bending processes, Journal of Iron and Steel Research International, 20(10) (2013) 64-69.
[14] [14] S.K. Panthi, N. Ramakrishnan, M. Ahmed, S.S. Singh, M.D. Goel, Finite element analysis of sheet metal bending process to predict the springback, Materials & Design, 31(2) (2010) 657-662.
[15] Z.Q. Jiang, H. Yang, M. Zhan, X.D. Xu, G.J. Li, Coupling effects of material properties and the bending angle on the springback angle of a titanium alloy tube during numerically controlled bending, Materials & Design, 31(4) (2010) 2001-2010.
[16] K. Mori, K. Aktia, Y. Abe, Springback behavior in bending of ultra-high-strength steel sheets using CNC servo press, International Journal of Machine Tools and Manufacture, 47(2) (2007) 321-325.
[17] X. Li, Y. Yang, Y. Wang, J. Bao, S. Li, Effect of the material-hardening mode on the springback simulation accuracy of V-free bending, Journal of Materials Processing Technology, 123(2) (2002) 209-211.
[18] H. Y. Yu, Variation of elastic modulus during plastic deformation and its influence on springback, Material & Design, 30(3) (2009) 846-850.
[19] J.G. Liu, M.W. Fu, J. Lu, W.L. Chan, Influence of size effect on the springback of sheet metal foils in micro-bending, Computational Materials Science, 50(9) (2011) 2604-2614.
[20] S. Toros, S. Kilic, F. Ozturk, The effect of material thickness and deformation speed on springback behavior for DP600 steel, Advanced Materials Research, 264 (2011) 636-645.
[21] X. Liu, S. Zhao, Y. Qin, J. Zhao, W.A. Wan-Nawang, A parametric study on the bending accuracy in micro W-bending using Taguchi method, Measurement, 100 (2017) 233-242.
[22] Z. Tekıner, An experimental study on the examination of springback of sheet metals with several thicknesses and properties in bending dies, Journal of Materials Processing Technology, 145(1) (2004) 109-117.
[23] M. Sabzi, & M. Farzam, Hadfield manganese austenitic steel: a review of manufacturing processes and properties, Materials Research Express, 6(10) (2019) 1065c2.
[24] X. Ha, M.G. Oliveira, A. Andrade-Campos, P.Y. Manach, & S. Thuillier, Prediction of coupled 2D and 3D effects in springback of copper alloys after deep drawing, International Journal of Material Forming, 14(5) (2021) 1171-1187.
[25] A.A. Suvorova, I.V. Danilov, G.M. Kalinin, A.B. Korostelev, Heat treatment effects on the microstructure and properties of Cu–Cr–Zr alloy used for the ITER blanket components, Nuclear Materials and Energy, 15 (2018) 80-84.
[26] J. Wang, M. Fu, J. Ran, Analysis of the size effect on springback behavior in micro‐scaled U‐bending process of sheet metals, Advanced Engineering Materials, 16(4) (2014) 421-432.
[27] S. Thipprakmas, W. Phanitwong, Process parameter design of spring-back and spring-go in V-bending process using Taguchi technique, Materials & Design, 32(8-9) (2011) 4430-4436. | ||
|
آمار تعداد مشاهده مقاله: 306 تعداد دریافت فایل اصل مقاله: 286 |
||