| تعداد نشریات | 24 |
| تعداد شمارهها | 912 |
| تعداد مقالات | 8,158 |
| تعداد مشاهده مقاله | 15,836,762 |
| تعداد دریافت فایل اصل مقاله | 13,332,356 |
Investigation of Globularization and Mechanical Behavior of Ti-8Al-1Mo-1V Alloy During Post-Deformation and Heat Treatment | ||
| Iranian Journal of Materials Forming | ||
| دوره 13، شماره 3، 2026، صفحه 12-25 اصل مقاله (1.98 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22099/ijmf.2026.54721.1360 | ||
| نویسندگان | ||
| Gholamreza Ebrahimi1؛ Zahra Mirzaie2؛ Hamidreza Ezatpour* 3 | ||
| 1Department of Materials Science and Engineering, Faculty of Engineering, Ferdowsi University of Mashhad, Mashhad, Iran | ||
| 2Department of Materials and Polymers Engineering, Faculty of Engineering, Hakim Sabzevari University, Sabzevar, Iran | ||
| 3Department of Materials Engineering, Vali-e-Asr University of Rafsanjan, Rafsanjan, Iran | ||
| چکیده | ||
| In this study, the effect of hot compression and subsequent heat treatment on α globularization and mechanical properties of Ti-8Al-1Mo-1V (Ti-811) alloy with an initial lamellar microstructure was investigated. Heat treatment was performed on hot-deformed samples (at 1000 °C and 0.001 s-1), at temperatures of 800, 850, and 900 °C for durations ranging from 1 h to 5 h. The results showed that the microstructural changes depended on the temperature and time of heat treatment and globular α phase fraction increased with increasing time and temperature. By increasing the heat treatment temperature from 800 °C to 900 °C for 5 h, the volume fraction of globular α phase increased from 68% to 79% and the aspect ratio decreased from 7.2 to 6.2. Microstructural studies showed that the globularization mechanism was controlled by boundary splitting, interface migration, and Ostwald growth. At lower temperatures of 800 °C and 850 °C, the dominant mechanism was boundary splitting by the shearing of α layers, which depended on the amount of pre-strain. At the higher temperature of 900 °C, globularization was controlled by interface migration and Ostwald growth, which were diffusion processes and dependent on heat treatment time. The static globurization kinetics of Ti-811 during heat treatment was well modeled by the modified JMRE equation, with a correlation coefficient (R) of 0.97 and the mean absolute relative error (MARE) of 7.19%. A punching test was applied to evaluate the mechanical properties of the deformed and heat-treated samples. The maximum shear strength and elongation were obtained at 900 °C and a holding time of 2 h, which were equal to 695 MPa and 1.1, respectively. | ||
| کلیدواژهها | ||
| Ti-811 alloy؛ Hot compressive test؛ Heat treatment؛ Globularization؛ Mechanical properties | ||
| مراجع | ||
|
[1] Shean Lee, R., & Chang Lin, H. (1998). Process design based on the deformation mechanism for the non-isothermal forging of Ti–6Al–4V alloy. Journal of Materials Processing Technology, 79(1), 224-235. https://doi.org/10.1016/S0924-0136(98)00016-8
[2] Qi, Y., Wang, X., Tian, P., Zhuang, W., Li, Y., Chu, Z., Ding, X., & Sun, J. (2025). Explosive compression strengthened a near-α titanium alloy with high strength. Journal of Alloys and Compounds, 1030, 180896. https://doi.org/10.1016/j.jallcom.2025.180896
[3] Jiang, X. J., Zhang, L. W., Sun, G. W., Yang, J. H., Ran, Q. X., & Wu, H. Y. (2023). Excellent mechanical properties of a Ti-based alloy via optimizing grain boundary α phase. Materials Letters, 333, 133662. https://doi.org/10.1016/j.matlet.2022.133662
[4] Zarghani, F., Ebrahimi, G. R., Taheri, J., & Ezatpour, H. R. (2023). Hot compressive deformation behavior of Ti-8Al-1Mo-1V titanium alloy at elevated temperatures: Focus on flow behavior, constitutive modeling, and processing maps. Materials Today Communications, 37, 107235. https://doi.org/10.1016/j.mtcomm.2023.107235
[5] Ding, Z., & Jiao, Z. B. (2021). Metallic materials for making multi-scaled metallic parts and structures. Encyclopedia of Materials: Metals and Alloys, 4, 19-36. https://doi.org/10.1016/B978-0-12-819726-4.00007-7
[6] Shi, X., Zeng, W., Long, Y., & Zhu, Y. (2017). Microstructure evolution and mechanical properties of near-α Ti-8Al-1Mo-1V alloy at different solution temperatures and cooling rates. Journal of Alloys and Compounds, 727, 555-564. https://doi.org/10.1016/j.jallcom.2017.08.165
[7] Lin, X., Huang, H., Yuan, X., Wang, Y., Zheng, B., Zuo, X., & Zhou, G. (2022). Study on hot deformation behavior and processing map of a Ti-47.5Al-2.5V-1.0Cr-0.2Zr alloy with a fully lamellar microstructure. Journal of Alloys and Compounds, 901, 163648. https://doi.org/10.1016/j.jallcom.2022.163648
[8] Seshacharyulu, T., Medeiros, S. C., Morgan, J. T., Malas, J. C., Frazier, W. G., & Prasad, Y. V. R. K. (2000). Hot deformation and microstructural damage mechanisms in extra-low interstitial (ELI) grade Ti–6Al–4V. Materials Science and Engineering: A, 279(1), 289-299. https://doi.org/10.1016/S0921-5093(99)00173-2
[9] Yang-huan-zi, L., Ji, G., & Min, S. (2024). Phase transformation in titanium alloys: A review. Transactions of Nonferrous Metals Society of China, 34(10), 3093-3117. https://doi.org/10.1016/S1003-6326(24)66597-0
[10] Xu, J., Zeng, W., Ma, H., & Zhou, D. (2018). Static globularization mechanism of Ti-17 alloy during heat treatment. Journal of Alloys and Compounds, 736, 99-107. https://doi.org/10.1016/j.jallcom.2017.11.117
[11] Xu, J., Zeng, W., Jia, Z., Sun, X., & Zhou, J. (2014). Static globularization kinetics for Ti-17 alloy with initial lamellar microstructure. Journal of Alloys and Compounds, 603, 239-247. https://doi.org/10.1016/j.jallcom.2014.03.082
[12] Abbasi, S. M., & Momeni, A. (2011). Effect of hot working and post-deformation heat treatment on microstructure and tensile properties of Ti-6Al-4V alloy Transactions of Nonferrous Metals Society of China, 21(8), 1728-1734. https://doi.org/10.1016/S1003-6326(11)60922-9
[13] Rani, S. U., Kesavan, D., & Kamaraj, M. (2023). Possible globularization mechanism in LPBF additively manufactured Ti-6Al-4V alloys. Materials Characterization, 205, 113303. https://doi.org/10.1016/j.matchar.2023.113303
[14] Wang, K., Zeng, W., Zhao, Y., Lai, Y., & Zhou, Y. (2010). Dynamic globularization kinetics during hot working of Ti-17 alloy with initial lamellar microstructure. Materials Science and Engineering: A, 527(10), 2559-2566. https://doi.org/10.1016/j.msea.2010.01.034
[15] Stefansson, N., Semiatin, S. L., & Eylon, D. (2002). The kinetics of static globularization of Ti-6Al-4V. Metallurgical and Materials Transactions A, 33(11), 3527-3534. https://doi.org/10.1007/s11661-002-0340-x
[16] Park, C. H., Won, J. W., Park, J. W., Semiatin, S. L., & Lee, C. S. (2012). Mechanisms and kinetics of static spheroidization of hot-worked Ti-6Al-2Sn-4Zr-2Mo-0.1Si with a lamellar microstructure. Metallurgical and Materials Transactions A, 43(3), 977-985. https://doi.org/10.1007/s11661-011-1019-y
[17] Stefansson, N., & Semiatin, S. (2003). Mechanisms of globularization of Ti-6Al-4V during static heat treatment. Metallurgical and Materials Transactions A, 34(3), 691-698. https://doi.org/10.1007/s11661-003-0103-3
[18] Chong, Y., Bhattacharjee, T., Gholizadeh, R., Yi, J., & Tsuji, N. (2019). Investigation on the hot deformation behaviors and globularization mechanisms of lamellar Ti–6Al–4V alloy within a wide range of deformation temperatures. Materialia, 8, 100480. https://doi.org/10.2139/ssrn.3438562
[19] Zherebtsov, S., Murzinova, M., Salishchev, G., & Semiatin, S. (2011). Spheroidization of the lamellar microstructure in Ti–6Al–4V alloy during warm deformation and annealing. Acta Materialia, 59(10), 4138-4150. https://doi.org/10.1016/j.actamat.2011.03.037
[20] Cakan, B. C., Soyarslan, C., Bargmann, S., & Hahner, P. (2017). Experimental and computational study of ductile fracture in small punch tests, Metlas, 10(10), 1185. https://doi.org/10.3390/ma10101185
[21] Skripnyak, V. V., Iohim, K. V., & Skripnyak, V. A. (2023). Mechanical behavior of titanium alloys at moderate strain rates characterized by the punch test technique. Materials, 16(1), 416. https://doi.org/10.3390/ma16010416
[22] Torres, J., & Gordon, A. P. (2021). Mechanics of the small punch test: a review and qualification of additive manufacturing materials. Journal of Materials Science, 56(18), 10707-10744. https://doi.org/10.1007/s10853-021-05929-8
[23] Fu, Q., Yuan, W., & Xiang, W. (2021). Dynamic softening mechanisms and microstructure evolution of TB18 titanium alloy during uniaxial hot deformation. Metals, 11, 789. https://doi.org/10.3390/met11050789
[24] Mutombo, K., Siyasiya, C., & Stumpf, W. E. (2014). Dynamic globularization of α-phase in Ti6Al4V alloy during hot compression. Materials Science Forum, 783-786, 584-590. https://doi.org/10.4028/www.scientific.net/MSF.783-786.584
[25] Zhou, C., Cao, F., Yang, Z., & Rao, W. (2024). Dynamic recrystallization constitutive model and texture evolution of metastable β titanium alloy TB8 during thermal deformation. Materials, 17(7), 1572. https://doi.org/10.3390/ma17071572
[26] Ezatpour, H. R., Torabi Parizi, M., Ebrahimi, G. R., & Huo, Y. (2023). Punching shear failure behavior of fine-grained ZK60 Mg alloy processed by a novel forward shear normal extrusion process at room and elevated temperatures. Engineering Failure Analysis, 153, 107568. https://doi.org/10.1016/j.engfailanal.2023.107568
[27] Alizadeh, R., & Mahmudi, R. (2010). Evaluating high-temperature mechanical behavior of cast Mg-4Zn-xSb magnesium alloys by shear punch testing. Materials Science and Engineering: A, 527(16), 3975-3983. https://doi.org/10.1016/j.msea.2010.03.007
[28] Yu, Y., Qiang, F., Cai, J., Li, C., Wang, W., & Wang, K. (2025). Hot deformation behavior and microstructural evolution of as-cast TC4 titanium alloy. Journal of Materials Science, 60(21), 8870-8889. https://doi.org/10.1007/s10853-025-10938-y
[29] Wang, X., Liu, P., Liang, C., Lu, T., Feng, T., Niu, H., Dong, Y., & Liu, X. (2024). Investigation on the thermal deformation mechanisms and constitutive model of Ti-55511 titanium alloy. Journal of Materials Research and Technology, 33, 6780-6797. https://doi.org/10.1016/j.jmrt.2024.11.057
[30] Jonas, J. J., Aranas, C., Fall, A., & Jahazi, M. (2017). Transformation softening in three titanium alloys. Materials & Design, 113, 305-310. https://doi.org/10.1016/j.matdes.2016.10.039
[31] Yu, J., Li, Z., Qian, C., Huang, S., & Xiao, H. (2023). Investigation of deformation behavior, microstructure evolution, and hot processing map of a new near-α Ti alloy. Journal of Materials Research and Technology, 23, 2275-2287. https://doi.org/10.1016/j.jmrt.2023.01.177
[32] Wanjara, P., Jahazi, M., Monajati, H., Yue, S., & Immarigeon, J. P. (2005). Hot working behavior of near-α alloy IMI834. Materials Science and Engineering: A, 396(1-2), 50-60. https://doi.org/10.1016/j.msea.2004.12.005
[33] Zhang, Z. X., Qu, S. J., Feng, A. H., Shen, J., & Chen, D. L. (2017). Hot deformation behavior of Ti-6Al-4V alloy: effect of initial microstructure. Journal of Alloys and Compounds, 718, 170-181. https://doi.org/10.1016/j.jallcom.2017.05.097
[34] Ezatpour, H. R., Ebrahimi, G. R., & Zarghani, F. (2024). Effect of processing parameters on the morphology of α-phase in Ti-6Al-4V alloy during the two-step hot deformation. Iranian Journal of Materials Forming, 10(3), 54-62. https://doi.org/10.22099/ijmf.2024.49049.1277
[35] Ebrahimi, G. R., Zarghani, F., Ezatpour, H. R., & Taheri, J. (2024). Hot working behaviour of Ti–8Al–1Mo–1V alloy through the hot compression test. Materials Science and Technology, 40(10), 755-765. https://doi.org/10.1177/02670836231223807
[36] Gao, P., Fu, M., Zhan, M., Lei, Z., & Li, Y. (2020). Deformation behavior and microstructure evolution of titanium alloys with lamellar microstructure in hot working process: a review. Journal of Materials Science & Technology, 39, 56-73. https://doi.org/10.1016/j.jmst.2019.07.052
[37] Li, H., Zhao, Z., Guo, H., Yao, Z., Ning, Y., Miao, X., & Ge, M. (2017). Effect of initial alpha lamellar thickness on deformation behavior of a near-α high-temperature alloy during thermomechanical processing. Materials Science and Engineering: A, 682, 345-353. https://doi.org/10.1016/j.msea.2016.11.063
[38] Li, H., Zhao, Z., Ning, Y., Guo, H., & Yao, Z. (2018). Characterization of microstructural evolution for a near-α titanium alloy with different initial lamellar microstructures. Metals, 8(12), 1045. https://doi.org/10.3390/met8121045
[39] Wu, C. b., Yang, H., Fan, X. g., & Sun, Z. c. (2011). Dynamic globularization kinetics during hot working of TA15 titanium alloy with colony microstructure. Transactions of Nonferrous Metals Society of China, 21(9), 1963-1969. https://doi.org/10.1016/S1003-6326(11)60957-6
[40] Song, H. W., Zhang, S. H., & Cheng, M. (2009). Dynamic globularization kinetics during hot working of a two phase titanium alloy with a colony alpha microstructure. Journal of Alloys and Compounds, 480(2), 922-927. https://doi.org/10.1016/j.jallcom.2009.02.059
[41] Ma, X., Zeng, W., Tian, F., & Zhou, Y. (2012). The kinetics of dynamic globularization during hot working of a two phase titanium alloy with starting lamellar microstructure. Materials Science and Engineering: A, 548, 6-11. https://doi.org/10.1016/j.msea.2012.03.022
[42] Chen, H., & Cao, C. (2011). Static globularization of TC11 alloy during hot working process. Rare Metal Materials and Engineering, 40(6), 946-950. https://doi.org/10.1016/S1875-5372(11)60038-6
[43] Fan, X. G., Yang, H., Yan, S. L., Gao, P. F., & Zhou, J. H. (2012). Mechanism and kinetics of static globularization in TA15 titanium alloy with transformed structure. Journal of Alloys and Compounds, 533, 1-8. https://doi.org/10.1016/j.jallcom.2012.03.113
[44] Pang, H. y., Luo, J., Zhang, Z. g., Han, W. c., Xu, K. f., & Li, M. q. (2022). Quantitative analysis of globularization and modeling of TC17 alloy with basketweave microstructure. Transactions of Nonferrous Metals Society of China, 32(3), 850-867. https://doi.org/10.1016/S1003-6326(22)65838-2
[45] Zhang, J., Li, H., & Zhan, M. (2020). Review on globularization of titanium alloy with lamellar colony. Manufacturing Review, 7, 18. https://doi.org/10.1051/mfreview/2020015
[46] Zhang, J., Li, H., Sun, X., & Zhan, M. (2020). A multi-scale MCCPFEM framework: Modeling of thermal interface grooving and deformation anisotropy of titanium alloy with lamellar colony. International Journal of Plasticity, 135, 102804. https://doi.org/10.1016/j.ijplas.2020.102804
[47] Shugurov, A. (2021). Microstructure and mechanical properties of titanium alloys. Metals, 11(10), 1617. https://doi.org/10.3390/met11101617
[48] Liu, K., Zhang, H., Xiu, M., Huang, Z., Huang, H., Xu, Y., Zhou, R., & Xiao, H. (2023). Microstructure evolution, mechanical properties, and corrosion resistance of hot rolled and annealed Ti-Mo-Ni alloy. Metals, 13(3), 566. https://doi.org/10.3390/met13030566
[49] Majchrowicz, K., Sotniczuk, A., Malicka, J., Choińska, E., & Garbacz, H. (2023). Thermal stability and mechanical behavior of ultrafine-grained titanium with different impurity content. Materials (Basel), 16(4). https://doi.org/10.3390/ma16041339 | ||
|
آمار تعداد مشاهده مقاله: 149 تعداد دریافت فایل اصل مقاله: 99 |
||