| تعداد نشریات | 24 |
| تعداد شمارهها | 917 |
| تعداد مقالات | 8,230 |
| تعداد مشاهده مقاله | 16,274,709 |
| تعداد دریافت فایل اصل مقاله | 13,751,966 |
Microstructure and mechanical properties of Al-TiC composite fabricated by accumulated extrusion bonding (AEB) | ||
| Iranian Journal of Materials Forming | ||
| دوره 12، شماره 4، 2025، صفحه 34-43 اصل مقاله (1.92 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22099/ijmf.2025.53979.1344 | ||
| نویسندگان | ||
| Ali Jafari؛ Nozar Anjabin* | ||
| Department of Materials Science and Engineering, School of Engineering, Shiraz University, Shiraz, Iran | ||
| چکیده | ||
| There is a growing demand for the use of light metals such as Al and its alloys in various industrial applications due to their high strength-to-weight ratio. Many studies were conducted to improve their properties by developing fine-grained structures and/or adding reinforcing particles. In this study, Al-TiC composite samples were fabricated using the accumulated extrusion bonding (AEB) method, which is a severe plastic deformation technique. The effects of particle volume fraction and the number of extrusion passes on the microstructure and mechanical properties of the composites were investigated. The results indicated that the AEB of the pure Al sample at 390°C with a 90% reduction in cross-sectional area resulted in proper interlayer bonding. The composite samples were fabricated by incorporating varying content of TiC particles (0.5, 1, and 2 vol.%) between the layers. It was found that the strength and hardness of the composite increased with the volume fraction of reinforcing particles. After four AEB passes, the composite sample containing 2 vol.% TiC exhibited a uniform distribution of TiC particles, resulting in an 83% increase in tensile strength and a 156% increase in hardness compared to the annealed sample. | ||
| کلیدواژهها | ||
| Aluminum composite؛ TiC؛ accumulated extrusion bonding؛ mechanical properties | ||
| مراجع | ||
|
[1] Li, C., & Feng, Q. (2023). Light alloys and their applications. Metals, 13(3), 561-563. https://doi.org/10.3390/met13030561
[2] Ghalehbandi, S. M., Malaki, M., & Gupta, M. (2019). Accumulative roll bonding—a review. Applied Sciences, 9(17), 3627-3638. https://doi.org/10.3390/app9173627
[3] Ravikumar, M., Reddappa, H., & Suresh, R. (2018). Aluminium composites fabrication technique and effect of improvement in their mechanical properties–A review. Materials Today: Proceedings, 5(11), 23796-23805. https://doi.org/10.1016/j.matpr.2018.10.171
[4] Oyewo, A. T., Oluwole, O. O., Ajide, O. O., Omoniyi, T.E., & Hussain, M. (2024). A summary of current advancements in hybrid composites based on aluminium matrix in aerospace applications. Hybrid Advances, 5, 100117-100130. https://doi.org/10.1016/j.hybadv.2023.100117
[5] Yonetken, A., Çakmakkaya, M., & Oguz, Y. (2015). Production and characterization of Al-TiC composite materials, Proceedings of the 1st International Conference on Engineering and Natural Sciences, Macedonia.
[6] Habba, M. I., Barakat, W. S., Elnekhaily, S. A., & Hamid, F. (2024). Microstructure and tribological behavior of Al–TiC composite strips fabricated by a multi-step densification method. Scientific Reports, 14(1), 20767-20787. https://doi.org/10.1038/s41598-024-70560-x
[7] Huang, Q., He, R., Wang, C., & Tang, X. (2019). Microstructure, corrosion and mechanical properties of TiC particles/Al-5Mg composite fillers for tungsten arc welding of 5083 aluminum alloy. Materials, 12(18), 3029-3043. https://doi.org/10.3390/ma12183029
[8] Krishna Prasad, S., Dayanand, S., Rajesh, M., Nagaral, M., Auradi, V., & Selvaraj, R. (2022). Preparation and mechanical characterization of TiC particles reinforced Al7075 alloy composites. Advances in Materials Science and Engineering, (1), 7105189-7105199. https://doi.org/10.1155/2022/7105189
[9] Jafarian, H., Habibi-Livar, J., & Razavi, S.H. (2015). Microstructure evolution and mechanical properties in ultrafine grained Al/TiC composite fabricated by accumulative roll bonding. Composites Part B: Engineering, 77, 84-92. https://doi.org/10.1016/j.compositesb.2015.03.009
[10] Wang, W., Heydari Vini, M., & Daneshmand, S. (2022). Mechanical and wear properties of Al/TiC composites fabricated via combined compo-casting and APB process. Crystals, 12(10), 1440-1450. https://doi.org/10.3390/cryst12101440
[11] Muralidharan, G. K., & Verlinden, B. (2016). Novel severe plastic deformation technique-accumulated extrusion (AccumEx). Materials Science and Technology, 32(6), 547-555. https://doi.org/10.1179/1743284715Y.0000000121
[12] Han, T., Huang, G., Ma, L., Wang, G., Wang, L., & Pan, F. (2019). Evolution of microstructure and mechanical properties of AZ31 Mg alloy sheets processed by accumulated extrusion bonding with different relative orientation. Journal of Alloys and Compounds, 784, 584-591. https://doi.org/10.1016/j.jallcom.2019.01.091
[13] Standley, M. R., & Knezevic, M. (2021). Towards manufacturing of ultrafine-laminated structures in metallic tubes by accumulative extrusion bonding. Metals, 11(3), 389-413. https://doi.org/10.3390/met11030389
[14] Tekkaya, A., Groche, P., Kinsey, B., & Wang, Z. (2023). Stress superposition in metal forming. CIRP annals, 72(2), 621-644. https://doi.org/10.1016/j.cirp.2023.04.090
[15] Xiang, C., Huang, G. S., & Jiang, B. (2019). Grain refinement and mechanical properties of pure aluminum processed by accumulative extrusion bonding. Transactions of Nonferrous Metals Society of China, 29(3), 437-447. https://doi.org/10.1016/S1003-6326(19)64953-8
[16] Xin, Y., Hong, R., Feng, B., Yu, H., Wu, Y., & Liu, Q. (2015). Fabrication of Mg/AL multilayer plates using an accumulative extrusion bonding process. Materials Science and Engineering: A, 640, 210-216. https://doi.org/10.1016/j.msea.2015.06.008
[17] Wu, G., Yu, Z., Jiang, L., Zhou, C., Deng, G., Deng, X., & Xiao, Y. (2019). A novel method for preparing graphene nanosheets/Al composites by accumulative extrusion-bonding process. Carbon, 152, 932-945. https://doi.org/10.1016/j.carbon.2019.06.077
[18] Alizadeh, M., & Paydar, M. (2010). Fabrication of nanostructure Al/SiCP composite by Materials Science and Technology accumulative roll-bonding (ARB) process. Journal of Alloys and Compounds, 492(1-2), 231-235. https://doi.org/10.1016/j.jallcom.2009.12.026
[19] Dai, L., Ling, Z., & Bai, Y. (2001). Size-dependent inelastic behavior of particle-reinforced metal–matrix composites. Composites Science and Technology, 61(8), 1057-1063. https://doi.org/10.1016/S0266-3538(00)00235-9
[20] Rezayat, M., Akbarzadeh, A., & Owhadi, A. (2012). Production of high strength Al–Al2O3 composite by accumulative roll bonding, Composites Part A: Applied Science and Manufacturing, 43(2), 261-267. https://doi.org/10.1016/j.compositesa.2011.10.015
[21] Trajano, A. A., Corrêa, E. C. S., Aguilar, M. T. P., & Cetlin, P. R. (2024). Accumulative roll bonding (ARB) and Cross accumulative roll bonding (CARB) in aluminum: A review. Materials Science and Technology, 02670836241303270. https://doi.org/10.1177/02670836241303270
[22] Kwan, C., Wang, Z., & Kang, S. B. (2008). Mechanical behavior and microstructural evolution upon annealing of the accumulative roll-bonding (ARB) processed Al alloy 1100, Materials Science and Engineering: A, 480(1-2), 148-159. https://doi.org/10.1016/j.msea.2007.07.022
| ||
|
آمار تعداد مشاهده مقاله: 275 تعداد دریافت فایل اصل مقاله: 243 |
||