| تعداد نشریات | 24 |
| تعداد شمارهها | 934 |
| تعداد مقالات | 8,383 |
| تعداد مشاهده مقاله | 16,982,182 |
| تعداد دریافت فایل اصل مقاله | 14,371,532 |
Effect of Heat Treatment and Rolling on the Microstructure and Tensile Behavior of Twin-Roll Cast AA8006 Aluminum Foils | ||
| Iranian Journal of Materials Forming | ||
| دوره 10، شماره 4، دی 2023، صفحه 25-33 اصل مقاله (2.36 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22099/ijmf.2024.48696.1273 | ||
| نویسندگان | ||
| M. Talebi؛ A.R. Eivani* ؛ S.M.A. Boutorabi | ||
| School of Metallurgy and Materials Engineering, Iran University of Science and Technology, Tehran, Iran | ||
| چکیده | ||
| The Microstructure and tensile properties of 60 µm thick AA8006 aluminum foil were investigated in the present study. Sheets of AA8006 were produced by twin-roll casting (TRC) with a thickness of 8 mm and were reduced to 4.5 mm thickness by one pass of rolling. The sheets were heat-treated, homogenized and annealed. After heat treatment, both processes were subjected to cold rolling to compare their tensile properties in 60 µm thickness after final annealing at different temperatures. The results showed that after homogenization, the short rod like eutectic phase is dispersed homogeneously in Al matrix of homogenized TRC processed alloy. The EDS results show that the contents of iron and manganese elements in the eutectic phase of TRC processed alloys decrease after homogenization, with the difference that this decrease is more noticeable in the thickness of 4.5 mm after annealing. It was also found that the homogenized sheet with a thickness of 60 micrometers after a rolling step was compared to the homogenized sheet after casting, due to smaller spherical intermetallic particles and better grain structure after heat treatment, the relative elongation from 12% to 27.5% showed an increase. | ||
| کلیدواژهها | ||
| Aluminum؛ Rolling؛ Microstructure؛ Mechanical properties | ||
| مراجع | ||
|
[1] Santos, C. A., Spim Jr, J. A., & Garcia, A. (2000). Modeling of solidification in twin-roll strip casting. Journal of Materials Processing Technology, 102(1-3), 33-39. https://doi.org/10.1016/S0924-0136(00)00448-9
[2] Yun, M., Lokyer, S., & Hunt, J. D. (2000). Twin roll casting of aluminium alloys. Materials Science and Engineering: A, 280(1), 116-123. https://doi.org/10.1016/S0921-5093(99)00676-0
[3] Haga, T., Ikawa, M., Wtari, H., & Kumai, S. (2006). 6111 Aluminium alloy strip casting using an unequal diameter twin roll caster. Journal of Materials Processing Technology, 172(2), 271-276. https://doi.org/10.1016/j.jmatprotec.2005.10.007
[4] Haga, T., & Suzuki, S. (2003). A twin-roll caster to cast clad strip. Journal of materials processing technology, 138(1-3), 366-371. https://doi.org/10.1016/S0924-0136(03)00100-6
[5] Watari, H., Davey, K., Rasgado, M. T., Haga, T., & Izawa, S. (2004). Semi-solid manufacturing process of magnesium alloys by twin-roll casting. Journal of Materials Processing Technology, 155, 1662-1667. https://doi.org/10.1016/j.jmatprotec.2004.04.323
[6] Lentz, M., Laptyeva, G., & Engler, O. (2016). Characterization of second-phase particles in two aluminium foil alloys. Journal of Alloys and Compounds, 660, 276-288. https://doi.org/10.1016/j.jallcom.2015.11.111
[7] Küçük, İ. (2018). Effect of cold rolling reduction rate on corrosion behaviour of twin-roll cast 8006 Aluminium alloys. Cumhuriyet Science Journal, 39(1), 233-242. http://doi.org/10.17776/csj.390178
[8] Karlık, M., Homola, P., & Slámová, M. (2004). Accumulative roll-bonding: first experience with a twin-roll cast AA8006 alloy. Journal of alloys and compounds, 378(1-2), 322-325. https://doi.org/10.1016/j.jallcom.2003.10.082
[9] Sun, N., Patterson, B. R., Suni, J. P., Simielli, E. A., Weiland, H., & Allard, L. F. (2006). Microstructural evolution in twin roll cast AA3105 during homogenization. Materials Science and Engineering: A, 416(1-2), 232-239. https://doi.org/10.1016/j.msea.2005.10.018
[10] Slámová, M., Sláma, P., & Cieslar, M. (2006). The influence of alloy composition on phase transformations and recrystallization in twin-roll cast Al-Mn-Fe alloys. Materials science forum, 519-521, 365-370. https://doi.org/10.4028/www.scientific.net/MSF.519-521.365
[11] Sun, N., Patterson, B. R., Suni, J. P., Weiland, H., & Allard, L. F. (2006). Characterization of particle pinning potential. Acta materialia, 54(15), 4091-4099. https://doi.org/10.1016/j.actamat.2006.05.008
[12] Sanguinetti Ferreira, R. A., Ribeiro Freitas, F. G., & Rocha Lima, E. P. (2000). Study of decomposition in AA 8023 aluminium alloy: kinetics and morphological aspects. Scripta materialia, 43(10), 929-934. https://doi.org/10.1016/S1359-6462(00)00515-7
[13] Birol, Y. (2009). Homogenization of a twin-roll cast thin Al–Mn strip. Journal of Alloys and Compounds, 471(1-2), 122-127. https://doi.org/10.1016/j.jallcom.2008.04.005
[14] Chen, Z., Zhao, J., & Chen, P. (2012). Microstructure and mechanical properties of nanostructured A8006 ribbons. Materials Science and Engineering: A, 552, 189-193. https://doi.org/10.1016/j.msea.2012.05.029
[15] Vončina, M., Kresnik, K., Volšak, D., & Medved, J. (2020). Effects of homogenization conditions on the microstructure evolution of aluminium alloy EN AW 8006. Metals, 10(3), 419. https://doi.org/10.3390/met10030419
[16] Engler, O., Laptyeva, G., & Wang, N. (2013). Impact of homogenization on microchemistry and recrystallization of the Al–Fe–Mn alloy AA 8006. Materials Characterization, 79, 60-75. https://doi.org/10.1016/j.matchar.2013.02.012
[17] Shakiba, M., Parson, N., & Chen, X. G. (2014). Effect of homogenization treatment and silicon content on the microstructure and hot workability of dilute Al–Fe–Si alloys. Materials Science and Engineering: A, 619, 180-189. https://doi.org/10.1016/j.msea.2014.09.072
[18] Roy, R. K., Kar, S., & Das, S. (2009). Evolution of microstructure and mechanical properties during annealing of cold-rolled AA8011 alloy. Journal of Alloys and Compounds, 468(1-2), 122-129. https://doi.org/10.1016/j.jallcom.2008.01.041
[19] Goulart, P. R., Lazarine, V. B., Leal, C. V., Spinelli, J. E., Cheung, N., & Garcia, A. (2009). Investigation of intermetallics in hypoeutectic Al–Fe alloys by dissolution of the Al matrix. Intermetallics, 17(9), 753-761. https://doi.org/10.1016/j.intermet.2009.03.003
[20] Wang, X., Guan, R. G., Misra, R. D. K., Wang, Y., Li, H. C., & Shang, Y. Q. (2018). The mechanistic contribution of nanosized Al3Fe phase on the mechanical properties of Al-Fe alloy. Materials Science and Engineering: A, 724, 452-460. https://doi.org/10.1016/j.msea.2018.04.002
[21] Chen, Z. W., Li, S. S., & Jing, Z. (2012). Homogenization of twin-roll cast A8006 alloy. Transactions of Nonferrous Metals Society of China, 22(6), 1280-1285. https://doi.org/10.1016/S1003-6326(11)61316-2
[22] Moldovan, P., Popescu, G., & Miculescu, F. (2004). Microscopic study regarding the microstructure evolution of the 8006 alloy in the plastic deformation process. Journal of materials processing technology, 153, 408-415. https://doi.org/10.1016/j.jmatprotec.2004.04.345 | ||
|
آمار تعداد مشاهده مقاله: 461 تعداد دریافت فایل اصل مقاله: 505 |
||