| تعداد نشریات | 24 |
| تعداد شمارهها | 935 |
| تعداد مقالات | 8,388 |
| تعداد مشاهده مقاله | 16,988,523 |
| تعداد دریافت فایل اصل مقاله | 14,377,063 |
Comparison of Plastic Anisotropy and Crystallographic Texture Evolution of Aluminum 1100 Between 90° and 135° ECAE Processes | ||
| Iranian Journal of Materials Forming | ||
| مقاله 3، دوره 10، شماره 1، فروردین 2023، صفحه 26-38 اصل مقاله (2.53 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22099/ijmf.2023.46818.1248 | ||
| نویسندگان | ||
| A. Hasani* ؛ S. Feyzi | ||
| Mechanical Engineering Group, Faculty of Engineering, University of Kurdistan, PB 416, PC 66177-15175, Sanandaj, Kurdistan Province, Iran | ||
| چکیده | ||
| A rolled sheet of aluminum 1100 was processed by two ECAE dies with inner corner angles of 90° and 135°. The samples were processed using route A up to 4 and 10 passes in ECAE 90° and 135°, respectively. The mechanical behaviors of initial and processed materials were evaluated by nano-indentation and compression tests carried out at three different orthogonal directions, at room temperature. Crystallographic texture evolution during two different ECAE processes has been also studied. A considerable reduction in mechanical anisotropy is displayed for processed materials compared to the initial material by nano-indentation tests. Though there is appreciable progress in mechanical isotropy for processed materials by 135° ECAE, compared to the 90° case. Studying crystallographic texture evolutions reveals that ECAE 135° is more capable than ECAE 90° in the development of cube components; however, the rate of texture evolution is slower in ECAE 135°. Dissimilar prominent texture components are also developed by two different ECAE processes. | ||
| کلیدواژهها | ||
| Anisotropy؛ ECAE؛ Nano-indentation test؛ Texture evolution؛ Aluminum 1100 | ||
| مراجع | ||
|
[1] R.Z. Valiev, T.G. Langdon, Principles of equal-channel angular pressing as a processing tool for grain refinement, Progress in Materials Science, 51(7) (2006) 881-981.
[2] R.Z. Valiev, Y. Estrin, Z. Horita, T.G. Langdon, M.J. Zechetbauer, Y.T. Zhu, Producing bulk ultrafine-grained materials by severe plastic deformation, JOM, 58 (2006) 33-39.
[3] V.M. Segal, Equal channel angular extrusion: from macromechanics to structure formation, Materials Science and Engineering: A, 271(1-2) (1999) 322-333.
[4] I.J. Beyerlein, L.S. Tóth, Texture evolution in equal-channel angular extrusion, Progress in Materials Science, 54(4) (2009) 427-510.
[5] Z. Horita, T. Fujinami, T.G. Langdon, The potential for scaling ECAP: effect of sample size on grain refinement and mechanical properties, Materials Science and Engineering: A, 318(1-2) (2001) 34-41.
[6] Y.T. Zhu, T.C. Lowe, T.G. Langdon, Performance and applications of nanostructured materials produced by severe plastic deformation, Scripta Materialia, 51(8) (2004) 825-830.
[7] R.Z. Valiev, M.J. Zehetbauer, Y. Estrin, H.W. Höppel, Y. Ivanisenko, H. Hahn, G. Wilde, H.J. Roven, X. Sauvage, T.G. Langdon, The innovation potential of bulk nanostructured materials, Advanced Engineering Materials, 9(7) (2007) 527-533.
[8] C. Xu, Z. Száraz, Z. Trojanová, P. Lukáč, T.G. Langdon, Evaluating plastic anisotropy in two aluminum alloys processed by equal-channel angular pressing, Materials Science and Engineering: A, 497(1-2) (2008) 206-211.
[9] F.S.J. Poggiali, C.L.P. Silva, P.H.R. Pereira, R.B. Figueiredo, P.R. Cetlin, Determination of mechanical anisotropy of magnesium processed by ECAP. Journal of Materials Research and Technology, 3(4) (2014) 331-337.
[10] I.J. Beyerlein, S. Li, and D.J. Alexander, Modeling the plastic anisotropy in pure copper after one pass of ECAE, Materials Science and Engineering: A, 410 (2005) 201-206.
[11] I.J. Beyerlein, D.J. Alexander, C.N. Tomé, Plastic anisotropy in aluminum and copper pre-strained by equal channel angular extrusion, Journal of Materials Science, 42 (2007) 1733-1750.
[12] I.J. Beyerlein, C.N. Tomé, Modeling transients in the mechanical response of copper due to strain path changes, International Journal of Plasticity, 23(4) (2007) 640-664.
[13] M. Prell, C. Xu, T.G. Langdon, The evolution of homogeneity on longitudinal sections during processing by ECAP, Materials Science and Engineering: A, 480(1-2) (2008) 449-455.
[14] C. Xu, M. Furukawa, Z. Horita, T.G. Langdon, The evolution of homogeneity and grain refinement during equal-channel angular pressing: A model for grain refinement in ECAP, Materials Science and Engineering: A, 398(1-2) (2005) 66-76.
[15] C. Xu, T.G. Langdon, The development of hardness homogeneity in aluminum and an aluminum alloy processed by ECAP, Journal of Materials Science, 42 (2007) 1542-1550.
[16] A. Karimzadeh, M.R. Ayatollahi, M. Alizadeh, Finite element simulation of nano-indentation experiment on aluminum 1100, Computational Materials Science, 81 (2014) 595-600.
[17] L. Qian, M. Li, Z. Zhou, H. Yang, X. Shi, Comparison of nano-indentation hardness to microhardness, Surface and Coatings Technology, 195(2-3) (2005) 264-271.
[18] ISO 14577, in Part 2: Verification and Calibration of Testing Machines, Part 3: Calibration of Reference Blocks, Geneva, Switzerland, 2002.
[19] Y. Hu, L. Shen, H. Yang, M. Wang, T. Liu, T. Liang, J. Zhang, Nanoindentation studies on nylon 11/clay nanocomposites, Polymer Testing, 25(4) (2006) 492-497.
[20] T. Liu, I.Y. Phang, L. Shen, S.Y. Chow, W.D. Zhang, Morphology and mechanical properties of multiwalled carbon nanotubes reinforced nylon-6 Composites, Macromolecules, 37(19) (2004) 7214-7222.
[21] A.C. Fischer-Cripps, Nanoindentation, Springer, New York, 2011, pp. 181-198.
[22] S. Suwas, R.A. Massion, L.S. Tóth, J.J. Fundenberger, B. Beausir, Evolution of texture during equal channel angular extrusion of commercially pure aluminum: experiments and simulations, Materials Science and Engineering: A, 520(1-2) (2009) 134-146.
[23] B. Beausir, J.J. Fundenberger, Analysis tools for electron and X-ray diffraction, ATEX–software, Université de Lorraine, Metz, France, 2017.
[24] L.S. Tóth, R.A. Massion, L. Germain, S.C. Baik, S. Suwas, Analysis of texture evolution in equal channel angular extrusion of copper using a new flow field, Acta Materialia, 52(7) (2004) 1885-1898. | ||
|
آمار تعداد مشاهده مقاله: 382 تعداد دریافت فایل اصل مقاله: 462 |
||