| تعداد نشریات | 24 |
| تعداد شمارهها | 934 |
| تعداد مقالات | 8,383 |
| تعداد مشاهده مقاله | 16,981,645 |
| تعداد دریافت فایل اصل مقاله | 14,371,246 |
The Effect of Simple Shear Extrusion on the Texture and Porosity Content of Al/Al2O3 Composites | ||
| Iranian Journal of Materials Forming | ||
| دوره 9، شماره 2، تیر 2022، صفحه 26-35 اصل مقاله (3.2 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22099/ijmf.2022.42711.1211 | ||
| نویسندگان | ||
| M. Zabihi؛ F. Qods* ؛ E. Emadoddin* | ||
| Faculty of Materials and Metallurgical Engineering, Semnan University, Semnan 35131-19111, Iran | ||
| چکیده | ||
| In this study, aluminum/alumina composites with 1 and 3 vol% reinforcement particles were produced using powder metallurgy (PM); this was then followed by simple shear extrusion (SSE). Three SSE inserts with different distortion angles (α) were used in the SSE equipment. Three pressure values of 400, 600 and 800 MPa were selected for powder compression. Additionally, three different temperatures of 530, 550 and 570°C were chosen to evaluate the suitable sintering temperature and achieve the optimal SSE process. The effect of post-sintering annealing treatment on SSE feasibility was also investigated. In addition, porosity was measured by the Archimedes method and the microstructure of samples was evaluated using optical and scanning electron microscopy. Evaluation of the crystalline texture was examined by the X-ray method. It was found that the pressure of 800 MPa was the optimal value for the cold compression of powders and the temperature of 570℃ was the best sintering temperature. It was also observed that the temperatures 400℃ and 450℃ had no effect on increasing the number of SSE passes. Porosity of the Al-3 vol% alumina sample was changed from 5.75% to 5.02% after three SSE passes with α=10°. A preferred crystallographic texture was not seen due to the amount of effective strain and the presence of micro-pores, but a very low intensity cube texture {001} <100> was seen in some regions. | ||
| کلیدواژهها | ||
| Powder metallurgy technique؛ Simple shear extrusion؛ Porosity measurement؛ Crystallographic texture؛ Aluminum/alumina composite | ||
| مراجع | ||
|
[1] C. Dhadsanadhep, T. Luangvaranunt, J. Umeda, K. Kondoh, Fabrication of Al/Al2O3 composite by powder metallurgy method from aluminum and rice husk ash, Journal of Metals, Materials and Minerals, 18(2) (2008) 99-102.
[2] M.J. Koczak, S.C. Khatri, J.E. Allison, M.G. Bader, in: S. Suresh, A. Mortensen, A. Needleman (Eds.), Fundamentals of metal matrix composites, Butterworth–Heinemann, Boston, 1993.
[3] K. Edalati, M. Ashida, Z. Horita, T. Matsui, H. Kato, Wear resistance and tribological features of pure aluminum and Al-Al2O3 composites consolidated by high-pressure torsion, Wear, 310(1-2) (2014) 83-89.
[4] A. Baradeswaran, A.E. Perumal, Study on mechanical and wear properties of Al 7075/Al2O3/graphite hybrid composites, Composites Part B: Engineering, 56 (2014) 464-471.
[5] S. Pournaderi, S. Mahdavi, F. Akhlaghi, Fabrication of Al/Al2O3 composites by in-situ powder metallurgy (IPM), Powder Technology, 229 (2012) 276-284.
[6] B.C. Kandpal, J. kumar, H. Singh, Fabrication and characterisation of Al2O3/aluminium alloy 6061 composites fabricated by stir casting, Materials Today: Proceedings, 4(2) (2017) 2783-2792.
[7] X. Chang, G. Chen, W. Sun, H. Zhang, G. Chu, X. Zhang, F. Han, W. Zhang, Z. Du, Microstructures, mechanical properties and solidification mechanism of a hot tearing sensitive aluminum alloy asymmetric part fabricated by squeeze casting, Journal of Alloys and Compounds, 886 (2021) 161254.
[8] S.K. Chaudhury, C.S. Sivaramakrishnan, S.C. Panigrahi, A new spray forming technique for the preparation of aluminium rutile (TiO2) ex situ particle composite, Journal of Materials Processing Technology, 145(3) (2004) 385-390.
[9] M. Zabihi, M.R. Toroghinejad, A. Shafyei, Application of powder metallurgy and hot rolling processes for manufacturing aluminum/alumina composite strips, Materials Science and Engineering: A, 560 (2013) 567-574.
[10] J.D. Torralba, C.E. Da Costa, F. Velasco, P/M aluminum matrix composites: an overview, Journal of Materials Processing Technology, 133(1-2) (2003) 203-206.
[11] R.K. Everett, R.J. Arsenault, Metal matrix composites: processing and interfaces, Academic Press, Elsevier, United States, 1991.
[12] R. Ebrahimi, A. Rezvani, E. Bagherpour, Circular simple shear extrusion as an alternative for simple shear extrusion technique for producing bulk nanostructured materials, Procedia Manufacturing, 15 (2018) 1502-1508.
[13] N. Pardis, R. Ebrahimi, Deformation behavior in simple shear extrusion (SSE) as a new severe plastic deformation technique, Materials Science and Engineering: A, 527(1-2) (2009) 355-360.
[14] E. Bagherpour, F. Qods, R. Ebrahimi, H. Miyamoto, Microstructure evolution of pure copper during a single pass of simple shear extrusion (SSE): role of shear reversal, Materials Science and Engineering: A, 666 (2016) 324-338.
[15] H. Utsunomiya, R. Matsumoto, Deformation processes of porous metals and metallic foams, Procedia Materials Science, 4 (2014) 245 -249.
[16] M. Zabihi, E. Emadoddin, F. Qods, Processing of Al/Al2O3 composite using simple shear extrusion (SSE) manufactured by powder metallurgy (PM), Metals and Materials International, 26(1), (2020) 1-13.
[17] M. Zabihi, M.R. Toroghinejad, A. Shafyei, Shear punch test in Al/alumina composite strips produced by powder metallurgy and accumulative roll bonding, Materials Science and Engineering: A, 667 (2016) 383-390.
[18] S. Amirkhanlou, R. Jamaati, B. Niroumand, M.R. Toroghinejad, Fabrication and characterization of Al/SiCp composites by CAR process, Materials Science and Engineering: A, 528(13-14) (2011) 4462-4467.
[19] A. Hassani, E. Bagherpour, F. Qods, Influence of pores on workability of porous Al/SiC composites fabricated through powder metallurgy+ mechanical alloying, Journal of Alloys and Compounds, 591 (2014) 132-142.
[20] N. Bayat Tork, N. Pardis, R. Ebrahimi, Investigation on the feasibility of room temperature plastic deformation of pure magnesium by simple shear extrusion process, Materials Science and Engineering: A, 560 (2013) 34-39.
[21] F.V. Lenel, Powder metallurgy: principles and applications, Metal Powder Industries Federation, Princeton, NJ, 1980.
[22] F. Bedir, B. Ogel. In: 3. Uluslarası toz metalurjisi kongresi (Ankara, Turkey, Gazi University, 2002), p. 4.
[23] H.J. Bunge, Texture analysis in materials science, Butterworths, London, UK, 1982.
[24] T. Eschner, J.J. Fundenberger, Application of anisotropic texture components, Texture and Microstructures, 28(3-4) (1997) 181-195.
[25] S.R. Kalidindi, C.A. Bronkhorst, L. Anand, Crystallographic texture evolution during bulk deformation processing of FCC metals, Journal of the Mechanics and Physics of Solids, 40(3) (1992) 537-569.
[26] H. Sheikh, R. Ebrahimi, E. Bagherpour, Crystal plasticity finite element modeling of crystallographic textures in simple shear extrusion (SSE) process, Materials & Design, 109 (2016) 289-299.
[27] F.J. Humphreys, The thermo mechanical processing of Al/SiC particulate composites, Materials Science and Engineering: A, 135 (1991) 267-273.
[28] F.J. Humphreys, W.S. Miller, M.R. Djazeb, Microstructural development during thermomechanical processing of particulate metal matrix composites, Materials Science and Technology, 6(11) (1990) 1157-1166.
[29] R. Jamaati, S. Amirkhanlou, M.R. Toroghinejad, B. Niroumand, Effect of particle size on microstructure and mechanical properties of composites produced by ARB process, Materials Science and Engineering: A, 528(4-5) (2011) 2143-2148. | ||
|
آمار تعداد مشاهده مقاله: 601 تعداد دریافت فایل اصل مقاله: 512 |
||