| تعداد نشریات | 24 |
| تعداد شمارهها | 934 |
| تعداد مقالات | 8,383 |
| تعداد مشاهده مقاله | 16,981,658 |
| تعداد دریافت فایل اصل مقاله | 14,371,256 |
Numerical Analysis of Plastic Strain Inhomogeneity in Rectangular Vortex Extrusion (RVE) Process | ||
| Iranian Journal of Materials Forming | ||
| دوره 8، شماره 3، مهر 2021، صفحه 46-52 اصل مقاله (1.18 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22099/ijmf.2021.40696.1183 | ||
| نویسندگان | ||
| Hossein Ataei1؛ Mehrdad Shahbaz* 1؛ Hyoung Seop Kim2؛ Nima Pardis3 | ||
| 1Department of Materials Science and Engineering, School of Engineering, Urmia University, Urmia, Iran | ||
| 2Department of Materials Science and Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea | ||
| 3Department of Materials Science and Engineering, School of Engineering, Shiraz University, Shiraz, Iran | ||
| چکیده | ||
| In this study, the effect of geometrical parameters of rectangular vortex extrusion die, including twist angle (Φ), reduction in area (RA), and twist zone length (L), on deformation inhomogeneity is investigated using the finite element analysis and response surface methodology. Analysis of variance (ANOVA) was used to determine the primary parameters and accuracy of the mathematical model obtained from response surface methodology results. The results showed that the suggested mathematical model predicts the strain inhomogeneity with high accuracy. Additionally, it revealed that the input parameters of Φ, RA, L, the interaction between Φ and RA (Φ×RA), and interaction between RA and L (RA×L) are the main significant factors affecting the inhomogeneity. Perturbation plots and 3D surface diagrams were used to check the results of ANOVA, the sign, and the magnitude of the coefficient of the suggested mathematical model. RA | ||
| کلیدواژهها | ||
| Severe plastic deformation؛ Rectangular vortex extrusion؛ Strain inhomogeneity؛ Finite element analysis؛ Response surface methodology | ||
| مراجع | ||
|
[1] H. Ataei, M. Shahbaz, H.S. Kim, N. Pardis, Finite element analysis of severe plastic deformation by rectangular vortex extrusion, Metals and Materials International, 27 (2021) 676-682.
[2] M. Shahbaz, N. Pardis, R. Ebrahimi, B. Talebanpour, A novel single pass severe plastic deformation technique: vortex extrusion, Materials Science and Engineering: A, 530 (2011) 469-472.
[3] M. Shahbaz, N. Pardis, J.G. Kim, R. Ebrahimi, H.S. Kim, Experimental and finite element analyses of plastic deformation behavior in vortex extrusion, Materials Science and Engineering: A, 674 (2016) 472-479.
[4] M. Shahbaz, N. Pardis, J. Moon, R. Ebrahimi, H.S. Kim, Microstructural and mechanical properties of a material processed by streamline proposed vortex extrusion die, Metals and Materials International, 27(3) (2021) 522-529.
[5] Y. Beygelzimer, D. Orlov, A. Korshunov, S. Synkov, V. Varyukhin, I. Vedernikova, A. Reshetov, A. Synkov, L. Polyakov, I. Korotchenkova, Features of twist extrusion: method, structures & material properties, Solid State Phenomena, 114 (2006) 69-78.
[6] Y. Beygelzimer, V. Varyukhin, S. Synkov, D. Orlov, Useful properties of twist extrusion, Materials Science and Engineering: A, 503(1-2) (2009) 14-17.
[7] D. Orlov, Y. Beygelzimer, S. Synkov, V. Varyukhin, N. Tsuji, Z. Horita, Plastic flow, structure and mechanical properties in pure Al deformed by twist extrusion, Materials Science and Engineering: A, 519(1-2) (2009) 105-111.
[8] M. I. Latypov, I.V. Alexandrov, Y.E. Beygelzimer, S. Lee, H.S. Kim, Finite element analysis of plastic deformation in twist extrusion, Computational Materials Science, 60 (2012) 194-200.
[9] E. Bagherpour, N. Pardis, M. Reihanian, R. Ebrahimi, An overview on severe plastic deformation: research status, techniques classification, microstructure evolution, and applications, The International Journal of Advanced Manufacturing Technology, 100(5-8) (2019) 1647-1694.
[10] E. Bagherpour, M. Reihanian, N. Pardis, R. Ebrahimi, T. Langdon, Ten years of severe plastic deformation (SPD) in Iran, part I: equal-channel angular pressing (ECAP), Iranian Journal of Materials Forming, 5(1) (2018) 71-113.
[11] S.A. Asghar, A. Mousavi, S.R. Bahador, Investigation and numerical analysis of strain distribution in the twist extrusion of pure aluminum, JOM, 63(2) (2011) 69-76.
[12] U.M. Iqbal, V.S. Senthil Kumar, Modeling of twist extrusion process parameters of AA6082-T6 alloy by response surface approach, Journal of Engineering Manufacture, 228(11) (2014) 1458-1468.
[13] M.I. Latypov, M.G. Lee, Y. Beygelzimer, D. Prilepo, Y. Gusar, H.S. Kim, Modeling and characterization of texture evolution in twist extrusion, Metallurgical and Materials Transactions A, 47(3) (2016) 1248-1260.
[14] F. Javadzadeh Kalahroudi, A.R. Eviani, H.R. Jafarian, A. Amouri, R. Gholizadeh, Inhomogeneity in strain, microstructure and mechanical properties of AA1050 alloy during twist extrusion, Materials Science and Engineering: A, 667 (2016) 349-357.
[15] G. Ranjbari, A. Doniavi, M. Shahbaz, Analysis of strain inhomogeneity in vortex extrusion using finite element method and response surface methodology, Iranian Journal of Materials Forming, 7 (2) (2020) 26-31.
[16] S.V. Noor, A.R. Eivani, H.R. Jafarian, M. Mirzaei, Inhomogeneity in microstructure and mechanical properties during twist extrusion, Materials Science and Engineering: A, 652 (2016) 186-191.
[17] Design Expert 11, Stat-Ease, Inc.
[18] CATIA v5R21, Dassault systems corporation.
[19] DEFORM-3D V11, Scientific Forming Technologies Corporation (SFTC).
[20] G. Ranjbari, A. Doniavi, M. Shahbaz, Numerical modelling and simulation of vortex extrusion as a severe plastic deformation technique using response surface methodology and finite element analysis, Metals and Materials International, (2020).
[21] G. Ranjbari, A. Doniavi, M. Shahbaz, R. Ebrahimi, Effect of processing parameters on the strain inhomogeneity and processing load in vortex extrusion of Al–Mg–Si alloy, Metals and Materials International, 27 (2021) 683–690.
| ||
|
آمار تعداد مشاهده مقاله: 558 تعداد دریافت فایل اصل مقاله: 521 |
||