اخبار و اعلانات

 آمار

تعداد نشریات24
تعداد شماره‌ها851
تعداد مقالات7,575
تعداد مشاهده مقاله13,413,758
تعداد دریافت فایل اصل مقاله11,580,454
JAHANPOUR, J., HONARI-TORSHIZI, M., GHARIB, M. R.. (1394). VCNC CONTOUR FOLLOWING TASKS USING ROBUST QFT CONTROLLER. , 39(M1), 131-145. doi: 10.22099/ijstm.2015.2954
J. JAHANPOUR; M. HONARI-TORSHIZI; M. R. GHARIB. "VCNC CONTOUR FOLLOWING TASKS USING ROBUST QFT CONTROLLER". , 39, M1, 1394, 131-145. doi: 10.22099/ijstm.2015.2954
JAHANPOUR, J., HONARI-TORSHIZI, M., GHARIB, M. R.. (1394). 'VCNC CONTOUR FOLLOWING TASKS USING ROBUST QFT CONTROLLER', , 39(M1), pp. 131-145. doi: 10.22099/ijstm.2015.2954
JAHANPOUR, J., HONARI-TORSHIZI, M., GHARIB, M. R.. VCNC CONTOUR FOLLOWING TASKS USING ROBUST QFT CONTROLLER. , 1394; 39(M1): 131-145. doi: 10.22099/ijstm.2015.2954

VCNC CONTOUR FOLLOWING TASKS USING ROBUST QFT CONTROLLER

Iranian Journal of Science and Technology Transactions of Mechanical Engineering
مقاله 11، دوره 39، M1، تیر 2015، صفحه 131-145    اصل مقاله (439.87 K)
نوع مقاله: Research Paper
شناسه دیجیتال (DOI): 10.22099/ijstm.2015.2954
نویسندگان
J. JAHANPOUR* 1؛ M. HONARI-TORSHIZI1؛ M. R. GHARIB2
1Dept. of Mechanical Engineering, Mashhad Branch, Islamic Azad University, Mashhad, I. R. of Iran
2Dept. of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, I. R. of Iran
چکیده
In this paper, the Quantitative Feedback Theory (QFT) is proposed to design a
controller for feed drive of Virtual Computer Numerical Control (VCNC) systems. The designed
robust QFT controller is also compared to two commonly used controller design methods, i.e.
Fuzzy Control (FC) and Sliding Mode Control (SMC), for contour tracking problem. The position
commands required for contour following task are evaluated by the Non-Uniform Rational BSpline
(NURBS) curve interpolator with the S-shape feedrate profile for two contours, i.e. "heart"
and "omega" as the case studies. After modeling the feed drive of the VCNC system, the robust
QFT controller and also FC and SMC controllers are designed to achieve the allowable tolerance
contour error. The simulation results for the "heart" and "omega" contour following tasks with the
aforementioned controllers were analyzed and discussed. It is found that the designed QFT
controller not only achieves the tight contour error but also yields better satisfactory performance,
especially at the corners of the tool path, compared to the other controllers used in contour
following applications in VCNC systems.
کلیدواژه‌ها
QFT controller؛ VCNC؛ NURBS interpolator؛ contour tracking؛ contour error
آمار
تعداد مشاهده مقاله: 2,911
تعداد دریافت فایل اصل مقاله: 2,531


سامانه مدیریت نشریات علمی. قدرت گرفته از سیناوب