| تعداد نشریات | 24 |
| تعداد شمارهها | 874 |
| تعداد مقالات | 7,803 |
| تعداد مشاهده مقاله | 14,220,762 |
| تعداد دریافت فایل اصل مقاله | 12,165,066 |
Effect of Fe additive on plastic deformation for crush-boxes with closed-cell metal foams, Part I: Al-composite foam compression response | ||
| Iranian Journal of Materials Forming | ||
| مقاله 4، دوره 1، شماره 1، تیر 2014، صفحه 32-45 اصل مقاله (1.29 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22099/ijmf.2014.2278 | ||
| نویسندگان | ||
| S.Mohammad Hossein mirbagheri* ؛ Mohammad javad Khajehali | ||
| Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran, Iran. P.O. Box 15875-4413. | ||
| چکیده | ||
| Abstract In this paper, we investigate effect of Fe–intermetallic compounds on plastic deformation of closed-cell composite Aluminum Foam as filler of thin-walled tubes. However, deformation of the Aluminum foam-filled thin-walled tubes as crushed-box will be presented in Part (II). Composite foams of AlSi7SiC3 and AlSi7SiC3-(Fe) as closed cell were synthesized by powder metallurgy foaming method. Macro and Micro structures of the produced foams revealed a non-homogenous cell dependent on Fe-rich intermetallic compounds. The cellular structure of AlSi7SiC3 foam shows a non-uniform and small size of bubbles with a few central big voids in comparison with the AlSi7SiC3-(Fe) foams. Analysis of EDAX results show, there are (α+β)-Fe- intermetallic compound within foams with Fe < 2 wt. %, and (α+δ)-Fe-intermetallic compound for the foams with Fe > 2 wt. %, which presence of them, depended on the cooling rate during solidification of liquid foams. The uniaxial compressive stress–strain curves of the filled thin-walled tubs with the composite closed cell foams will be investigated in next part. The stress-strain curve of the AlSi7SiC3 foam shows a smooth plastic deformation behavior in the plastic region, throughout the compression tests. However with increasing the weight percent of Fe from 1 up to 3%, the curve shows some variety at the slope of curves within the plastic zone. Results shown all of the compression response is due to the micro-porosity in plateau region and presence of the Fe-Al-Si-intermetallic within the cells wall that both them have the role of a stress concentration point during compressive loading. | ||
| کلیدواژهها | ||
| Metal foam؛ Plastic deformation؛ compression response؛ absorption energy؛ Fe-Al-Si-intermetallic compound | ||
| مراجع | ||
|
[1] J. Baumeister, J. Banhart, M.Weber, Aluminum foams for transport industry, Materials & & Design, 18(4/6), (1997) 217-220.
[2] T. Mukai, T. Miyoshi, S. Nakano, H. Somekawa, K. Higashi, Compressive response of a closed-cell Aluminum foam at high strain rate, Scripta Materialia, 54 (2006) 533–537.
[3] D. Lehmhus, J. Banhart, M.A. Rodriguez-Perez, Adaptation of Aluminum foam properties by means of precipitation hardening, Materials Science and Technology, 18 (2002) 1–6.
[4] A.G. Evans M.F. Ashby, N.A. Fleck, L.J. Gibson, J.W. Hutchinson, H.N.G. Wadley, Metal foams: A design guide, Elsevier, UK, (2000), chapter: 11.
[5] M. F. Ashby L. J. Gibson, Cellular Solids: Structure and Properties. Solid State Science., UK: Cambridge, (1997), chapter:4.
[6] W. abramowicz and T. Wierzbicki, Axial crushing of foam-filled columns, Journal of Mechanical Science, 30, Issues 3-4 (1988) 263-271.
[7] M. Langseth, A.G. Hanssen, and O.S. Hopperstad, Optimum design for energy absorption of square Aluminum columns with Aluminum foam filler, International Journal of Mechanical Sciences, 43 (2001)153-176.
[8] A.F. Bastawros, H. Bart-Smith, and A.G. Evans, Experimental analysis of deformation mechanisms in a closed-cell aluminum alloy foam. Journal of the Mechanics and Physics of Solids, 48 (2000) 301-322.
[9] A.K. Toksoy and M. Guden, Partial A: Foam filling of commercial 1050H14 crash boxes: the effect box column thickness and foam relative density on energy absorption, Thin-walled structures, 48(2010) 482-494.
[10] W. Yan, E. Durif, Y. Yamada and C. Wen, Crushing Simulation of Foam-Filled Aluminum Tubes, Materials Transactions, 48, No. 7 (2007) 1901-1906.
[11] W. Deqing and S. Ziyuan, Effect of ceramic particles on cell size and wall thickness of aluminum foam, Materials Science and Engineering A, 361 (2003) 45–49.
[12] P. Mondal, M.D. Goel, and S. Das, Effect of strain rate and relative density on aluminum-fly ash composite foam, Materials & Design 30 (2008) 1268–1274.
[13] M.J. Khajeali, Compressive response of the composite metallic foam filled-tubes and effective parameters, M.Sc. Thesis, Amirkabir University, (2011).
[14] A. Daoud, ,Compressive response and energy absorption of foamed A359–Al2O3 particle composites, Journal of Alloys and Compounds, 486 (2009) 597–605.
[15] Y. Luo, S. Yu,W. Li, J. Liu, and M. Wei, Compressive behavior of SiCp/AlSi9Mg composite foams, Journal of Alloys and Compounds 460 (2008)294–298.
[16] S. Lee, B. Kim and S. Lee, Prediction of Solidification Paths in Al-Si-Fe Ternary System and Experimental Verification: Part I. Fe-Containing Hypoeutectic Al-Si Alloys, Materials Transactions, Vol. 52, No. 5 (2011) 1053-1062.
[17]. Sanghwan Lee, Bonghwan Kim and Sangmok Lee, Prediction of Solidification Paths in Al-Si-Fe Ternary System and Experimental Verification: Part II. Fe-Containing Eutectic Al-Si Alloys, Materials Transactions, 52, No. 6 (2011)1308-1315.
[18] E. Amsterdam, P. R. Onck, and J. TH. M. Dehosson, Fracture and microstructure of open cell Aluminum foam, Journal of Materials Science, 40 (2005) 5813–5819
[19] G. Mrówka-Nowotnik, J. Sieniawski, and M. Wierzbiñska, Intermetallic phase particles in 6082 aluminum alloy , Archives of Materials Science and Engineering, 28, Issue 2 (2007) 69-76.
[20] E. Amsterdam, N. Babcsán, Jeff T.M. De Hosson, P.R. Onck, and J. Banhart, Fracture behavior of metal foams made of recycled MMC by the melt route, Materials Transactions, 47(6) (2006) 2219-2222.
[21] L. Sweet, S.M. Zhu, S.X. Gao, J.A. Taylor, and M,A. Easton, The effect of iron content on the Iron-containing intermetallic phases in a cast 6060 Aluminum alloy, Metallurgical and materials transaction A, 42A (2011)1737-17-49.
[22] A.R. Kennedy, S. Asavavisitchai, Effects of TiB2 Particle Addition on the Properties of PM Al Foams, Scripta Materialia 50 (2004) 115–119.
[23] Anton Gorny, Characterization of Major Intermetallic Phases in solidified Al-xSi-yFe-zSr alloy, Ph.D. thesis (open accesses), McMaster University, (2012).
[24] M. Timpel, N. Wanderka , R. Grothausmann , and J. Banhar , Distribution of Fe-rich phases in eutectic grains of Sr-modified Al-10wt%Si-0.1wt% Fe casting alloy, Journal of Alloys and Compounds, 558 (2013) 18–25.
[25] J. Banhart, Manufacture, characterization and application of cellular metals and metal foam, Progress in Materials Science, 46 (2001) 559–632. | ||
|
آمار تعداد مشاهده مقاله: 1,698 تعداد دریافت فایل اصل مقاله: 1,588 |
||